margarthawthorne

Профиль

Регистрация: 3 года, 6 месяцев назад

How To: Apply a Motocross Graphics Kit

Ever purchased a mud bike graphics kit to freshen up your motocross bike, but been too scared to place it on for concern of destroying it in the process? Listed below are the secrets and techniques we have now been utilizing for years to get graphics on quickly and easily.

What are the options?

The old saying goes there are a couple of totally different ways to skin a cat, which also applies to sticker kits as there isn’t really a proper or incorrect way to do this. We now have suggested the following technique as it has ended up being the easiest way now we have skilled while getting good outcomes, and will be cleaner than some other ways involving soapy water to help getting the graphics on straight.

Other alternate options for making use of graphics to the bike using nothing but elbow grease, which can work out fine, but if you happen to haven’t utilized graphics before we wouldn’t recommend it! The downside is the graphics are sticky and not very malleable, so you'll have to get them straight the primary attempt or you might damage the kit making an attempt to rip them off to get them straight.

Another method is the wet application using soapy water to lubricate the plastics and the sticker kit so you can place the graphics on and slide them round until you may have them in the appropriate place. The downside is some believe that although the soapy water dries, there is always cleaning soap residue the stays beneath the filth bike graphics kit, compromising the adhesive energy and making the kit more likely to peel off over time.

Step 1: Remove the old graphic kit from areas which you want to apply graphics to, you want a clean and smooth surface for the perfect likelihood of your graphics looking good and staying on. There may be some glue residue left on your plastics which is best to clean off with an alcohol-based cleaner - it's essential not to use any oil-based mostly cleaners, as this can damage the glue after installation.

Step 2: When your bike is clean and dry, take your whole new graphics out of the packaging and work out the place every bit needs to go, it can be confusing generally with similarly shaped filth bike stickers, so a great way to remember is working everything out after which laying them on the ground within the pattern which they'll go onto your bike.

Step three: You might be ready to start applying! Choose a part of the bike which is smooth and comparatively flat for your first try reasonably than picking a rounded surface which will be tricky, we usually start on the entrance fender and work our way to the back of the bike from there.

Some individuals like to remove the plastics from the bike to apply graphics, but we've discovered that on a full kit, some parts of the bike won’t line up completely straight, so keeping the plastics on the bike will enable you to get everything lining up straighter. Chances are you'll need to remove your seat or sure pieces of plastic momentarily as some graphics are designed to fold over an edge and stick down on the highest of your fuel tank for example, which would be harder with your seat still attached.

Begin by holding the sticker to the desired location to see how well it will line up and where you want it to stick. Once you're glad, peel away a small part of the backing paper so you will have a small section of adhesive exposed. We always find a straight part to start on as while you line the first part up properly the remainder of the sticker should line up accurately with the plastic providing the sticker template is made well.

After you have a small section stuck to the plastic and earlier than you remove the rest of the sticker backing check to see if the sticker is lining up with the remainder of the plastic by holding it down to see the place it lines up. In case you are pleased you might be ready to complete this off, if not you may lift the sticker off and have another try till you get it right!

This is where the heat gun comes into play:

Take your heat gun or hair dryer set on a low setting and use it to warm the motocross graphics up on the sting which is being stuck down, hold the heat gun approximately 30cm from the goal as stickers are thin, so they don’t want much heat before they start to melt - take your time and be careful or you'll find yourself with a warped mess!

As you warm the sticker up you'll be able to slowly peel the backing paper off and work the sticker down utilizing your fingers, you can find the sticker is soft because of the heat and will mould to the form of the plastics easily. Because of the warmth, it can be less likely to bubble and the sticker can stretch or compress simply and kind to the shape you want it to.

Keep doing this until the sticker is completely on and you should have a straight, smooth sticker free from bubbles, and haven't any need to make use of a box cutter to trim the loose parts of your sticker kit.

Repeat this process on each panel however bear in mind a surface which is concave or convex will always be difficult to use without bubbles, some stickers for these panels come with a small section lower out to permit for an overlap. You may have to trim these further so do your best and don’t be scared to trim if need be!

If you have any questions regarding where and the best ways to make use of quadzilla graphics kit, you can call us at our web site.

Сайт: http://surron-graphics.co.uk

Форумы

Тем начато: 0

Ответов написано: 0

Роль форума: Участник