bridgettlfs
@bridgettlfs
Профиль
Регистрация: 2 года, 9 месяцев назад
How To: Apply a Motocross Graphics Kit
Ever purchased a dust bike graphics kit to clean up your motocross bike, but been too scared to put it on for concern of destroying it within the process? Listed here are the secrets and techniques we have now been utilizing for years to get graphics on quickly and easily.
What are the options?
The old saying goes there are a number of totally different ways to skin a cat, which also applies to sticker kits as there isn’t really a proper or improper way to do this. Now we have prompt the following methodology as it has ended up being the best way we have now skilled while getting good outcomes, and could be cleaner than another ways involving soapy water to assist getting the graphics on straight.
Different alternatives for making use of graphics to the bike using nothing but elbow grease, which can work out fine, however in the event you haven’t utilized graphics before we wouldn’t advocate it! The downside is the graphics are sticky and never very malleable, so you'll have to get them straight the first attempt or you could damage the kit attempting to rip them off to get them straight.
One other method is the wet application utilizing soapy water to lubricate the plastics and the sticker kit so you possibly can place the graphics on and slide them around until you could have them in the appropriate place. The downside is some consider that regardless that the soapy water dries, there is always cleaning soap residue the remains beneath the dirt bike graphics kit, compromising the adhesive energy and making the kit more likely to peel off over time.
Step 1: Remove the old graphic kit from areas which you want to apply graphics to, you desire a clean and smooth surface for one of the best likelihood of your graphics looking good and staying on. There may be some glue residue left on your plastics which is best to clean off with an alcohol-primarily based cleaner - it's necessary not to use any oil-based cleaners, as this can damage the glue after installation.
Step 2: When your bike is clean and dry, take all your new graphics out of the packaging and work out the place each piece needs to go, it may be confusing generally with equally shaped dust bike stickers, so a great way to recollect is working everything out and then laying them on the ground within the sample which they may go onto your bike.
Step three: You are ready to start applying! Choose a part of the bike which is smooth and comparatively flat to your first attempt reasonably than picking a rounded surface which may be tricky, we normally start on the entrance fender and work our way to the back of the bike from there.
Some folks like to remove the plastics from the bike to apply graphics, but we have found that on a full kit, some parts of the bike won’t line up perfectly straight, so keeping the plastics on the bike will help you get everything lining up straighter. You may wish to remove your seat or sure items of plastic momentarily as some graphics are designed to fold over an edge and stick down on the highest of your fuel tank for instance, which can be harder with your seat still attached.
Start by holding the sticker to the desired location to see how well it will line up and where you need it to stick. Once you might be pleased, peel away a small section of the backing paper so you might have a small section of adhesive exposed. We always find a straight section to start on as while you line the primary part up properly the remainder of the sticker should line up appropriately with the plastic providing the sticker template is made well.
Upon getting a small part stuck to the plastic and earlier than you remove the remainder of the sticker backing check to see if the sticker is lining up with the remainder of the plastic by holding it down to see where it lines up. If you are glad you might be ready to complete this off, if not you possibly can lift the sticker off and have another strive till you get it proper!
This is where the heat gun comes into play:
Take your heat gun or hair dryer set on a low setting and use it to warm the motocross graphics up on the sting which is being stuck down, hold the heat gun approximately 30cm from the target as stickers are thin, so that they don’t want much heat earlier than they start to soften - take your time and be careful or you will end up with a warped mess!
As you warm the sticker up you may slowly peel the backing paper off and work the sticker down utilizing your fingers, one can find the sticker is soft because of the heat and will mould to the form of the plastics easily. Because of the warmth, it shall be less likely to bubble and the sticker can stretch or compress easily and kind to the form you need it to.
Keep doing this until the sticker is totally on and it is best to have a straight, smooth sticker free from bubbles, and don't have any need to make use of a box cutter to trim the loose parts of your sticker kit.
Repeat this process on each panel but bear in mind a surface which is concave or convex will always be troublesome to use without bubbles, some stickers for these panels come with a small part cut out to allow for an overlap. You may need to trim these additional so do your greatest and don’t be scared to trim if need be!
If you beloved this short article in addition to you want to be given more information regarding motocross decals kindly stop by our web site.
Сайт: http://surron-graphics.co.uk
Форумы
Тем начато: 0
Ответов написано: 0
Роль форума: Участник