archercreswell

Профиль

Регистрация: 3 года, 9 месяцев назад

How To: Apply a Motocross Graphics Kit

Ever bought a dirt bike graphics kit to clean up your motocross bike, however been too scared to place it on for worry of destroying it in the process? Listed below are the secrets we have now been utilizing for years to get graphics on quickly and easily.

What are the options?

The old saying goes there are a number of completely different ways to skin a cat, which also applies to sticker kits as there isn’t really a right or mistaken way to do this. We have advised the next technique as it has ended up being the best way we now have experienced while getting good outcomes, and could be cleaner than another ways involving soapy water to help getting the graphics on straight.

Other alternatives for making use of graphics to the bike utilizing nothing however elbow grease, which can work out fine, however if you happen to haven’t applied graphics before we wouldn’t recommend it! The downside is the graphics are sticky and never very malleable, so you will have to get them straight the primary strive or you possibly can damage the kit making an attempt to tear them off to get them straight.

Another technique is the wet application using soapy water to lubricate the plastics and the sticker kit so you possibly can place the graphics on and slide them around till you've gotten them within the appropriate place. The downside is a few imagine that though the soapy water dries, there may be always cleaning soap residue the remains beneath the dust bike graphics kit, compromising the adhesive strength and making the kit more likely to peel off over time.

Step 1: Remove the old graphic kit from areas which you wish to apply graphics to, you need a clean and smooth surface for the very best chance of your graphics looking good and staying on. There could also be some glue residue left in your plastics which is easiest to clean off with an alcohol-based cleaner - it's necessary not to use any oil-based mostly cleaners, as this can damage the glue after installation.

Step 2: When your bike is clean and dry, take all of your new graphics out of the packaging and work out the place each piece needs to go, it may be confusing typically with similarly formed grime bike stickers, so a very good way to recollect is working everything out after which laying them on the ground in the sample which they will go onto your bike.

Step 3: You are ready to start making use of! Select a part of the bike which is smooth and comparatively flat on your first attempt slightly than picking a rounded surface which will be tricky, we usually start on the front fender and work our way to the back of the bike from there.

Some folks like to remove the plastics from the bike to use graphics, but we've got found that on a full kit, some parts of the bike won’t line up perfectly straight, so keeping the plastics on the bike will assist you to get everything lining up straighter. It's possible you'll need to remove your seat or sure items of plastic momentarily as some graphics are designed to fold over an edge and stick down on the top of your fuel tank for example, which can be harder with your seat nonetheless attached.

Start by holding the sticker to the desired location to see how well it will line up and the place you need it to stick. As soon as you might be completely happy, peel away a small part of the backing paper so you could have a small part of adhesive exposed. We always find a straight part to start on as once you line the primary part up properly the remainder of the sticker ought to line up accurately with the plastic providing the sticker template is made well.

After getting a small section stuck to the plastic and earlier than you remove the remainder of the sticker backing check to see if the sticker is lining up with the remainder of the plastic by holding it down to see where it lines up. If you are completely satisfied you're ready to complete this off, if not you possibly can lift the sticker off and have another strive till you get it right!

This is where the heat gun comes into play:

Take your heat gun or hair dryer set on a low setting and use it to warm the motocross graphics up on the sting which is being stuck down, hold the heat gun approximately 30cm from the target as stickers are thin, so that they don’t need a lot heat before they start to soften - take your time and be careful or you will end up with a warped mess!

As you warm the sticker up you can slowly peel the backing paper off and work the sticker down using your fingers, you will discover the sticker is soft because of the heat and will mould to the shape of the plastics easily. Because of the warmth, it might be less likely to bubble and the sticker can stretch or compress easily and type to the shape you want it to.

Keep doing this till the sticker is totally on and you need to have a straight, smooth sticker free from bubbles, and have no need to use a box cutter to trim the loose parts of your sticker kit.

Repeat this process on every panel however bear in mind a surface which is concave or convex will always be tough to use without bubbles, some stickers for these panels come with a small part cut out to permit for an overlap. It's possible you'll have to trim these additional so do your best and don’t be scared to trim if want be!

In the event you adored this informative article and you would like to obtain more details relating to quadzilla decals kindly stop by our own web site.

Сайт: http://www.stickerfxgraphics.co.uk

Форумы

Тем начато: 0

Ответов написано: 0

Роль форума: Участник